switch
-
- Member
- Posts: 201
- Joined: Tue Jun 24, 2008 3:16 pm
- Location: southern utah
switch
Looking at putting wireless in one of our older buildings built in 1972. Cinder block and brick construction. We was wondering if you can put a switch on the line coming into the computer in the clerks office and split off and put a Aironet 1041n in from there? We would be doing two office's like that if it will work.
-
- Community Administrator
- Posts: 34487
- Joined: Sat Jan 20, 2007 2:53 pm
- Location: U.S.
Not optimal, but doable. Don't forget the power injector for the 1041.
Have you searched the Help Center? Try doing a Google search and adding "site:churchofjesuschrist.org/help" to the search criteria.
So we can better help you, please edit your Profile to include your general location.
So we can better help you, please edit your Profile to include your general location.
-
- Senior Member
- Posts: 501
- Joined: Thu Jan 03, 2008 7:52 pm
Like Russ said, it will work, but why do it that way?farwest wrote:Looking at putting wireless in one of our older buildings built in 1972. Cinder block and brick construction. We was wondering if you can put a switch on the line coming into the computer in the clerks office and split off and put a Aironet 1041n in from there? We would be doing two office's like that if it will work.
The best way would be to pull a network cable from the room where the router is to where you want the wireless coverage. The wireless access points (WAP) can have a good range. I have one unit that was built about the same time and it is Cinder Block and brick and I put a D-Link wireless access point in there and I had full coverage.
I just recently added a 881W to that building because the PIX was becoming unreliable. Now, I'm pretty sure that I have better coverage in that building.
Now in the building that I attend my meetings, half of it is cinder block and brick and the other half is stick built. I will be replacing the PIX there with an 881W and all the aironet 1200 series with the 1041n. My plan is to put the WAPS above the ceiling and hopefully the 1041n has a good signal that I will be able to only use one 1041N and the 881W and get full coverage of the building. I will let you know next week what I did.
-
- Member
- Posts: 201
- Joined: Tue Jun 24, 2008 3:16 pm
- Location: southern utah
wireless old building
Talking with the internet provider employee who knows the building said it hard to string wire in this building because of the way it was built. So he suggested the switch at the clerks room where wire is already there. Looking forward to see how your wireless works because we getting ready to do this building. The aironet power supply for the power injector is going to be the same part number FM said.
- Mikerowaved
- Community Moderators
- Posts: 4740
- Joined: Sun Dec 23, 2007 12:56 am
- Location: Layton, UT
We ran into a similar situation in one of our buildings. The cost of pulling additional runs was very high, so we made do with what we had. Most of our AP's there (non-Cisco) are daisy-chained off of other runs. It reduces the reliability factor somewhat, because if one piece breaks it will take out an entire string, but it's been running flawlessly for several years now.farwest wrote:Talking with the internet provider employee who knows the building said it hard to string wire in this building because of the way it was built.
So we can better help you, please edit your Profile to include your general location.
-
- Church Employee
- Posts: 48
- Joined: Sun Mar 06, 2011 12:31 pm
- Location: Utah, USA
farwest wrote:Looking at putting wireless in one of our older buildings built in 1972. Cinder block and brick construction. We was wondering if you can put a switch on the line coming into the computer in the clerks office and split off and put a Aironet 1041n in from there? We would be doing two office's like that if it will work.
This will work but the initial configuration of the 1041 can take a bit of time. Fastest one I have seen is 15 minutes. When you first get the 1041, dont plug it into the switch but put it directly to the 881w for a day or 2 and then move it to the switch. We have seen problems when a new AP is installed and is connected to a switch instead of the 881w.